We will have all the replacement bearing parts you will need as we do not have a bearing kit with all the parts you need. First we have the Bearing # L68149 and its corresponding Race # L68111. It is likely that your spindle will use the Grease Seal # 58846 but you should verify your measurements (ID 1.719" / OD 2.565") with your current seal. We also have the Tang Washer # 5-101 for a 1" diameter spindle nut.
The Seal Puller # PTW1219 and 7-Piece Installation Set # PTW83020 will aid in... view full answer...
We can help you with both a hitch and 7-way wiring set-up for your 2016 Toyota RAV4 SE.
For your towing application I recommend a 2-inch Class III hitch, the etrailer # e98864 that you referenced. An install video and article are linked. With it you can use the ball mount # C45030 along with either 2-inch ball # 63845 or 2-5/16-inch ball # 63847. If you need a different ball mount the linked article will help you determine this.
For a universal-fit towing mirror to extend your view of... view full answer...
A factory towable bumper has additional features/bracing to aid in towing that the other option does not. A factory towable bumper on a Toyota Tundra has a hole located in the the bumper for a hitch ball, on the bumper step area in front of the license plate.
The trailer hitch receiver I recommend for your Tundra is the Curt Trailer Hitch Receiver part # 13184 because it will fit models both with the towable bumper and models with the non-towable bumper. This hitch has a Class III rating... view full answer...
We do indeed offer fan-powered coolers that can be used for either engine oil or transmission fluid. In really rough slow-speed off-road conditions a passive cooler like Derale # D13503 may not get enough air flow through it for it to do its job. In such cases a fan-powered cooler is definitely the way to go. Coolers are not fluid-specific, meaning that any given cooler can be used for engine oil or transmission fluid. The are not vehicle-specific either.
We offer both single-path and... view full answer...
The 2020 GM factory rail kits were changed from 2019 so the correct adapter you'd need is the part # DM6333 and not the Curt # C16023 that you referenced as it fits the first generation of GM rail kits. view full answer...
I would be happy to help!
First things first 5,200 - 7,000lb axles are all compatible with the same hubs so you can use the HydraStar Disc Brake Kit w/ Actuator for Tandem Axle Trailers - 13" Hub/Rotor - 8 on 6-1/2 - 7K # HSE7K-T1 on your 2021 Jayco Eagle 321RSTS. I see you mentioned an HSE6K-T1 kit but HydraStar does not offer such a kit.
The brake pads used are a bit different as they are designed for heavier trailers but they will still be OK. The biggest thing you need to check is... view full answer...
Baseplates are intended to only be used on one vehicle and to be considered compromised after removal from the first vehicle so the safest option would be to replace the entire Roadmaster Direct-Connect Base Plate Kit # 1541-5. You can try reaching out to Roadmaster to see if they have a replacement hardware kit but they'll likely tell you the same thing. view full answer...
You are correct. The light kit, # 20174, for Tow Ready Cargo Carriers, like # 63153, are sealed and there are no replacement bulbs. The lights used in the kit are 6-1/2 inch Oval Trailer Stop, Turn and Tail Light, 3-Function, # ST70RB.
We also have complete replacement light kits. First is the 20174 kit you have referenced. The other is the LED Light Kit for Draw-Tite, Tow Ready, and Rola Railed Cargo Carriers, # 98174LED. The only difference is that the 98174LED light kit uses LEDs and... view full answer...
If you are talking about a lift kit for a trailer then they are called over/under kits. There are 2 options. First we have # K71-384-00 for 2-3/8 inch diameter round axles. And second we have # K71-385-00 for 3 inch diameter round axles.
If neither will work then the other option to raise the height of the trailer is to use taller suspension hangers. I have included a link to our hanger main page for you. Current pricing for parts can be found on their respective product pages. view full answer...
There are powered tailgate locks available for your 2013 Toyota Tacoma. We have # PAL85403 for white and # PAL8550 for black. In order for the power tailgate locks to work the truck has to have power door locks. If it doesn't then you would need to add switch kit # PAL9520. view full answer...
We do offer disc brake kits, both complete kits that include a coupler and also brake-only kits with a 6-bolt lug pattern like those shown on the linked page. These 6-lug kits fit 5200- and 6000-lb axles.
You can choose from several finishes and these vary considerably in cost. A basic raw-finish kit costs less than a Dacromet-finish kit like # K2HR526D, which in turn costs far less than a stainless steel kit like # K2R526S. Please refer to the linked page to see all 6-lug kits.
You can... view full answer...
The jogging conversion kit for the Cougar 1 child carrier is # TH20100143. This same kit also fits the Cheetah 1. For the individual arms use # TH40101027 for the left and # TH40101028 for the right.
But these parts only fit models made in 2011 or later. I believe if you check the serial number of the Cougar the first 2 digits are the week and the second 2 digits are the year. So for example if the serial number was 2511-XXXX that would be the 25th week of 2011. view full answer...
To mount your first-generation Thule Flat Top rooftop ski and snowboard rack TH725 on your Rhino-Rack Vortex roof rack crossbars you can use Mounting Kit # 7533998. This kit includes new clamps and hardware. view full answer...
Yes, the RoadActive Suspension Custom Leaf Spring Enhancement Kit, # RAS3611-HD will fit your 1975 Ford F-250. This custom-fit kit comes fully assembled and is easy to install. Each RAS unit simply bolts onto your factory leaf spring with the included hardware, and drilling, welding, and cutting aren't required. First, position the eye hook bracket so that it wraps around the top of the factory leaf spring eye. Then the axle bracket secures under the leaf spring and around the factory U-bolts... view full answer...
For your 2002 Isuzu Rodeo the trailer kit I would recommend is the T-One kit part # 118360 which is a confirmed fit and installs by plugging inline with the vehicle taillight connectors. I attached an install video for this kit on a similar 2001 Isuzu Rodeo for you to check out as well. view full answer...
We do have one possible suspension enhancement option for your 2022 Kia Soul. What you may be able to use is the Air Lift 1000 Universal Air Spring Kit like the # AL60908. Keep in mind, no suspension enhancement will actually increase the carrying capacity of your vehicle. It is only designed to provide additional support while towing or hauling.
To find the correct kit you will need to take some measurements on your rear coil spring. Also, this kit will not fit vehicles with coil-over... view full answer...
Sure do! If your Tacoma has the factory installed 7-way connector, the wiring harness you'll need is # 3040-P. I've linked you to an install video that shows where the connector is located.
If you don't have the 7-way, you'll first need to install a functional 4 pole trailer connector like part # 118496. You'll then use our Brake Controller Installation Kit, part # ETBC7. If you don't have the quick disconnect pigtail for the Primus, you'll also need part # 7894. The install kit includes... view full answer...
We do have a couple options to lift your 2005 Keystone Cougar 5th wheel. The first would be to "flip" your axle using an over-under conversion kit. This moves your trailer's leaf springs to the top of your axle and will increase the height of your trailer the equivalent of the diameter of your axle plus the height of your leaf spring stack.
- Dexter Trailer Springs Over-Under Conversion Kit # K71-384-00 (For 2-3/8" diameter axles)
or
- Dexter Trailer Springs Over-Under Conversion Kit #... view full answer...
I do have all the parts that you would need to install disc brakes on your 5,200 lb tandem axle trailer, but not as a kit.
First, you will need the Kodiak Disc Brake Kit, part # K2R526S, which is a stainless slip-on disc brake kit. We also have a hub replacement disc brake kit, in a dacromet coating, part # K2HR526D. To use part # KSHR526D, you would need to pull apart your hub and make sure you have the correct bearings, races and seals. You will also need to have a 6 on 5-1/2 bolt pattern... view full answer...
Go To Results